原装 乐泰胶水101乐泰代理商发货

　　乐泰101

　　product deion

　　permatexò ultra copperò is a single component, room

　　temperature vulcanizing gasketing compound designed to

　　provide reliable “formed-in-place” gaskets for mechanical

　　assemblies. this material cures on exposure to moisture in

　　the air to form a tough, flexible, silicone rubber gasket. the

　　product resists aging, weathering and thermal cycling

　　without hardening, shrinking or cracking. designed for the

　　higher temperature environments encountered in 4-cylinder,

　　turbocharged, and performance engines. the most

　　advanced high performance, high temperature (up to 700°f

　　intermittent) rtv gasket available.

　　product benefits

　　· high temperature resistance

　　· sensor safe, non-corrosive

　　· superior adhesion and flexibility

　　· replaces most cut gaskets

　　· improved oil resistance

　　· can be used as a gasket maker or dressing

　　· non-flammable, non-toxic

　　· low odor

　　typical applications

　　· exhaust manifolds

　　· thermostat housings

　　· valve covers

　　· timing gear covers

　　· water pumps

　　· differential covers

　　directions for use

　　for assembly as form-in-place gasket

　　1. remove all previous material from mating surfaces.

　　permatexò gasket remover is recommended for

　　most materials, not for plastics or painted surfaces.

　　2. for best results, clean and dry all surfaces with a

　　residue-free solvent, such as permatexò brake and

　　parts cleaner.

　　3. cut nozzle to desired bead size, 1/16 “ to 1/4 “ in

　　diameter. an 1/8” bead is usually sufficient for most

　　applications.

　　4. remove cap, puncture tube or cartridge seal and attach

　　extension nozzle.

　　5. apply a continuous and even bead of silicone to one

　　surface, first tracing the internal areas of the gasket

　　configuration, then all surrounding bolt holes as shown

　　below:

　　6. assemble parts immediately while silicone is still wet.

　　secure or tighten to recommended torque specs.

　　7. re-torque will not be necessary after the product has

　　cured.

　　for assembly as gasket dressing

　　1. repeat steps 1 thru 4 as in previous section.

　　2. apply a thin film of silicone to one surface to be sealed.

　　3. place the pre-cut gasket onto silicone film.

　　4. apply a second thin to pre-cut gasket surface.

　　5. remove any excess and assemble parts immediately.

　　note: product not recommended for use as a cylinder

　　head gasket or head gasket sealant.

　　for cleanup

　　1. allow excess material to extend beyond the extension

　　nozzle or aerosol tip to cure, sealing and protecting the

　　remaining product from moisture. for reuse, simply

　　remove the cured product from the tip and exposure

　　original product for next application.

　　2. remove uncured product from parts and hand-tools

　　with a dry cloth, if skinned over, break film with a dry

　　cloth to remove as much as possible, and remove the

　　remaining material with permatexò gasket remover

　　as previously stated.

　　3. clean hands with a dry cloth or permatexò fast

　　orange hand cleaner.

　　typical environmental resistance

　　temperature resistance typical values

　　continuous, °c (°f) -59 to 316 (-75 to 600)

　　intermittent, °c (°f) -59 to 371 (-75 to 700)

　　chemical / solvent resistance

　　the product retains effective properties in contact with

　　automotive fluids, such as motor oil, transmission fluids,

　　alcohol and antifreeze solutions. note: not recommended

　　for parts in contact with gasoline.

　　general information

　　this product is not recommended for use in pure

　　oxygen and/or oxygen rich systems and should not be

　　selected as a sealant for chlorine or other strong

　　oxidizing materials.

　　storage

　　products shall be ideally stored in a cool, dry location in

　　unopened containers at a temperature between 8° to 28°c

　　(46° to 82°f) unless otherwise labeled. optimal storage is at

　　the lower half of this temperature range.

　　优势方面

　　我们是胶粘剂及施胶设备整体解决方案供应商，我们不止卖产品，我们更为客户提供全面而的售前指导和售后服务工作，直至广大客户的项目正常运转！

　　欲知更多产品详情，欢迎咨询深圳市鹏科泰贸易有限公司

　　以下价格仅供参考，具体价格面议！