镇江厂房地坪-推荐施工镇江环氧树脂地坪

　　镇江厂房地坪-推荐施工镇江环氧树脂地坪 承接环氧树脂地坪、混凝土密封固化剂地坪、金刚砂耐磨地坪、不发火（防爆）地坪、工业防腐、防静电、运动场地、止滑车道、停车场系列等现代企业厂房及室内外地坪装饰。广泛应用于工业厂房，例如电子、电器、医药、办公场所、食品、生物、化工、机械加工、超市、学校、停车场等领域。

　　晟航地坪 咨询热线 欢迎您的垂询！

　　晟航拥有自己的材料工厂，公司自成立以来坚持以的材料特性，有素的施工队伍和先进的技术设备（拥有成套打磨、吸尘、涂装的自动化设备），高品质的施工质量，完善的售后服务措施，现已成为全国地坪行业知名企业。加上我们的不断创新及工程技术服务的精益求精，公司业务迅速发展，现已覆盖全国多个地区。同时我们可以根据客户需求和地面情况设计出客户满意的工程施工方案。

　　企业宗旨：以质量求生存，以信誉求发展，一切为客户，一心为客户；

　　企业文化：社会责任、人本主义、对人充分信任和尊重；

　　企业精神：诚信严谨、团结一致、求真务实、创新发展、追求；

　　企业目标：做精做强、铸造辉煌。打造晟航装饰品牌；

　　企业口号：品质铸就非凡，服务成就辉煌；

　　团队精神：精诚合作、各尽所能、共创美好明天。

　　环氧树脂地坪

　　施工要求

　　1、要求水泥素地基面牢固、结实、不起壳，好是水泥与混凝土底一起浇注，以杜绝砂浆层起壳现象，混凝土基础干燥28天。一楼地面需做防水处理。

　　2、要求水泥基面表层不起砂、硬度好、没有水泥粉化现象。

　　3、表面平坦，无凹凸不平、蜂窝麻面、水泥疙瘩等现象。

　　4、地坪表面的PH值应在6.8—8.0之间。

　　起泡原因

　　环氧树脂地坪起水泡多发生在一楼或地下室，有时二楼以上也时有发生，环氧树脂地坪起水泡一般在施工后不久就发现，有的上午铺贴的环氧树脂地坪下午就有水泡。水泡由小到大，不断发展，发展到一定程度后停止。气温越高，水泡就越容易发生，发展的速度也越快。水泡形状各异，其大小不一。有的水泡直径达1m以上，高度达20~50mm。

　　起水泡的原因，是大家关心的一个问题，剖开水泡发现，泡内都含有水分或炎黄色液体，环氧地面层与基层脱离，粘在基层上的胶结料被拉成峰窝状，见图1—1；按照“物理学”解释，在盛有液体的密闭容器内，液体蒸发，形成饱和状态的三条曲线的温度与压力关系。

　　在密闭的容器内，含有饱和水蒸汽的压力，是随着温度的升高而上升，当温度为20.C时，鼓包内的压力为0.01MPa；而当温度为70~80.C之间是直线上升到0.1MPa；很多地区在炎热的夏季地面的极端辐射热可达70.C左右，在这样的高温下，环氧胶结料已经软化粘力大大降低，因此就形同向轮胎内渐渐鼓气一样，使环氧地面层中鼓起了大包，将胶结料被拉成蜂窝状；其中没有起水泡的部分环氧层和地面部分粘结不牢固，仔细观测接触部分，也会发现有无法固化的部分

　　1.基层、如水泥砂浆找平层，大含水率达12%左右，基层的大含水量大于找平层。

　　2.环氧中的其它配料内的脱水不尽。

　　3.环氧和基层施工时结合不好留下空隙和环氧本身的化学活性，没有完全固化或者是遇到潮湿气没有完全固化的残留物或气体。

　　4.基层的地下渗透的潮湿气体。

　　从以上四个方面来分析，基层的潮湿是主要的，干燥的基层是没有的。含水率的大小也不能决定环氧树脂地坪是否会产生水泡，基层的部份水气和环氧残留物被包裹在环氧与基层内，形成大小不一的气泡，由于环氧层本身不透水气，水气不能排出，留下起泡的根苗。所以泡都产生在平面上，多在基层与环氧层之间；基层中的水分是很难避免的。

　　特性

　　由特种环氧树脂添加适当溶剂，填料，表面活性剂和高级颜料等材料做为主剂，并采用改性脂肪胺做为固化剂，在常温条件下所形成的致密的三维交联涂层。具有：

　　1、 良好的耐磨性能；

　　2、 良好的抗碾压性能；

　　3、 优异的防渗透性能；

　　4、 中等条件下的防腐蚀性能；

　　5、 附着力良好，保证了涂层不龟裂、不脱落；

　　6、 外观平滑整洁，便于清洁维护；

　　7、 费用较低。

　　适用范围

　　电器、电子、机械、食品、医药、化工、烟草、饮料、纺织、服装、家具、塑料、文体用品等制造工厂的车间水泥或水磨石地面。

　　施工工艺

　　素地处理：首先对原地面进行全面打磨，不平处需修复平整，然后清扫、 吸尘，潮湿处需先烘干。

　　底层：用镘刀将调配好的纯树脂材料均匀地刮涂于原地面，与素地完全渗透 粘接，使其形成一层粘性较强的底层。

　　砂浆层：待底层固化后再将调配好的腻子层材料加石英砂全面均匀地用镘刀刮涂于底层之上，加强地坪的抗压、抗冲击性。（2mm将涂装两次）

　　中层：待砂浆层固化后再进行全面打磨，将调配好的中涂材料用镘刀平镘于砂浆层之上，填补砂浆层上不平的小凹坑及针孔，使之均匀平整。

　　面层：待中涂固化后，用打磨机全面研磨平整后清除干净，使中涂基面平整、光滑。将面涂材料调配搅拌后用镘刀均匀镘涂于中涂之上，形成一道防尘、防腐、耐磨、光洁、亮丽的自流平表层。

　　性能特点

　　环氧树脂地坪漆具有耐强酸碱、耐磨、耐压、耐冲击、防霉、防水、防尘、止滑以及防静电、电磁波等特性，颜色亮丽多样，清洁容易。它采用一次性涂覆工艺，不管有多大的面积，都不存在连接缝，而且还是一种无灰尘材料，具有附着力强，耐磨擦，硬度强等特点。

　　1、防尘、防潮、耐磨；

　　2、便于清洁、施工快捷、维护方便、造价低廉；

　　3、附着力强、柔韧性好、耐冲击；

　　4、厚度0.2-0.3㎜。

　　养护介绍

　　1. 建议行人穿软底鞋（若现场条件允许），进入工业地坪区前要清理干净鞋底上的砂粒等硬质物，以减少锐利物体对地坪表面的划伤。

　　2. 搬运物品尽量做到轻举轻放，防止重物冲击地面，以免造成人为损坏。

　　环氧树脂地坪

　　环氧树脂地坪

　　3. 车间内的环氧地坪上行车要注意速度不可过快，以免刹车行为造成剪切发热过高，从而使得环氧地坪漆瞬间软化（环氧地坪漆的软化温度在80℃左右，因此其使用环境温度一般控制在50℃以下）并在剪切力的作用下产生难以清洗的污痕。

　　4. 日常清洁可用地坪清洗机或湿抹布擦试，可选用中性清洁剂清洗，也可使用一般洗涤剂以较小浓度加入水中做成清洗液，然后使用地坪清洗机或棉布拖把洗净地坪表面的污渍，并用清水再洗一遍，擦干地面；注意地坪漆边缘部分不要较长时间有积水。

　　5. 不定期进行打蜡处理（一般每个月要打蜡一次），建议使用专用地板蜡或乳化水性蜡；先使用地坪清洗机或棉布拖把将地坪清洗干净并拭干，然后打蜡处理。打蜡处理可以增加任何地坪材料的耐磨性及抗划伤性.

　　6. 避免使用重物或是工具敲击地面，也不可直接在环氧地面上拖移重物。

　　7. 避免重腐蚀性介质长时间浸泡地坪漆膜，如不慎重腐蚀性酸碱洒落，请务必及时清理干净酸碱介质。

　　Zhenjiang factory floor - recommended construction of zhenjiang epoxy floor paint epoxy resin floor, sealed concrete curing agent floors, emery wear-resisting flooring, no spark (explosion) floor, industrial anti-corrosion, antistatic, sports venues, check block road, parking lot series and other modern enterprises plant and indoor and outdoor floor decoration.Widely used in industrial plants, such as electronics, electrical appliances, medicine, office, food, biology, chemical, mechanical processing, supermarkets, schools, parking lots and other fields.

　　Sheng course has its own material factory, the company since its inception adhere to high-quality materials properties, well-trained professional construction team and advanced technical equipment (with complete grinding, vacuuming, coating of automation equipment), the construction quality of high quality, perfect after-sale service measures, has become the national floor industry well-known enterprises.In addition to our continuous innovation and continuous improvement of engineering services, the company's business has developed rapidly and now covers many areas of the country.At the same time, we can design the project construction plan that the customer is satisfied according to the customer's demand and the ground situation.

　　Enterprise objective: to survive by quality, to develop by reputation, all for customers, for customers;

　　Corporate culture: social responsibility, humanism, full trust and respect for people;

　　Enterprise spirit: integrity, preciseness, unity, truth-seeking, pragmatic, innovative development, pursuit of excellence;

　　Enterprise goals: to do fine and strong, casting brilliant.Building shenghang decoration brand;

　　Enterprise slogan: quality cast extraordinary, service achievements brilliant;

　　Team spirit: sincere cooperation, every effort to create a better tomorrow.

　　Epoxy resin floor

　　Construction requirements

　　1. The cement foundation is required to be firm, solid and non-shelf-proof. It is best to pour the cement together with the concrete foundation to avoid the phenomenon of mortar shell rising, and the concrete foundation is dry for 28 days.The ground floor needs to be waterproof.

　　2. It is required that the surface layer of the cement substrate should be free from sand, good hardness and cement powder.

　　3. The surface is flat, without any bump, honeycomb surface, cement knobs and other phenomena.

　　4. The PH value of the ground surface should be between 6.8 and 8.0.

　　Foaming reason

　　Epoxy floor paint blisters tend to occur on the first floor or basement, sometimes more than on the second floor, epoxy floor paint blisters in commonly found shortly after the construction, some on the morning of the shop is stuck epoxy floor paint have blisters in the afternoon.Water bubble from small to large, continuous development, development to a certain extent after stop.The higher the temperature, the more likely the blisters are and the faster they develop.Bubbles come in all shapes and water bubbles have a diameter of more than 1m and a height of 20-50mm.

　　Blisters, is a question of people's concern, open blisters found that contained moisture inside the bubble or yanhuang color liquid, epoxy floor away from the grassroots and stuck on the primary cement be drawn into a peak,, as shown in figure 1, 1;According to the "physics" explanation, the temperature and pressure relation of three curves of saturation state are formed by the evaporation of liquid in a closed container containing liquid.

　　In a closed container, the pressure containing saturated water vapor rises with the increase of temperature. When the temperature is 20.c, the pressure inside the drum is 0.01mpa.When the temperature is between 70 and 80, C rises directly to 0.1MPa.Many areas in the hot summer extreme radiant heat up to 70. The ground around C, in such a high temperature, epoxy cement has softened viscous force greatly reduced, thus to the tire is gradually strengthening, bolstered epoxy ground floor in the parcel, will cement be drawn into a honeycomb;The part of epoxy layer that does not have blister is not firmly bonded to the ground part. If you observe the contact part carefully, you will also find that there are parts that cannot be cured

　　1. The maximum water content of the base layer, such as the cement mortar leveling layer, is about 12%, and the maximum water content of the base layer is greater than that of the leveling layer.

　　2. The dehydration of other ingredients in epoxy is inexhaustible.

　　3. The combination of epoxy and base construction is not good enough to leave the gap and the chemical activity of epoxy itself. There is no complete solidification or residues or gases that have not been completely cured in the presence of moisture.

　　4. Moist gas permeated underground at the base.

　　From the above four aspects of analysis, the base moisture is the main, absolute dry base is not.The size of the moisture content can't decide whether epoxy floor paint can produce blisters, grassroots part of moisture and epoxy residue was wrapped in epoxy and at the grass-roots level, size of bubble formation, due to the impermeable gas, epoxy floor moisture can't discharge, sparkling the bubbles are produced on the plane, mostly between the base and the epoxy layer;Water in the base is hard to avoid.

　　features

　　Special epoxy resin by adding appropriate solvent, and filler, surface active agent and senior agent, the material such as paint and using modified aliphatic amine as curing agent, the density of the formed under the condition of the three-dimensional crosslinked coating.A:

　　1. Good wear resistance;

　　2. Good anti-rolling performance;

　　3. Excellent penetration resistance;

　　4. Corrosion resistance under moderate conditions;

　　5. Good adhesion, ensuring that the coating does not crack and fall off;

　　6. Smooth and neat appearance, convenient for cleaning and maintenance;

　　7. Low cost.

　　Scope of application

　　Cement or terrazzo floors in workshops of manufacturing plants, such as electrical appliances, electronics, machinery, food, medicine, chemicals, tobacco, beverages, textiles, clothing, furniture, plastics, stationery, etc.

　　The construction technology

　　Surface treatment: first, the original ground shall be thoroughly polished, and the uneven areas shall be repaired and leveled, then cleaned and dusted, and the wet areas shall be dried first.

　　Bottom layer: use a trowel to evenly scrape and apply the prepared pure resin material to the original ground, and completely permeate and adhere to the plain ground, so that it forms a layer of strong viscosity of the bottom layer.

　　Mortar layer: after the bottom layer is solidified, the prepared putty layer material and quartz sand are applied uniformly and comprehensively with trowel knife to the bottom layer, so as to strengthen the pressure and impact resistance of the ground floor.(2mm will be painted twice)

　　Middle: stay mortar layer curing thoroughly again after polishing, the mixture of coating material with a trowel trowel on the mortar layer, fill the mortar layer on the uneven small pits and pinhole, make uniform flat and level.

　　Surface layer: after the middle coating is solidified, it is cleaned after grinding and leveling with the grinding machine, so that the middle coating base surface is smooth and smooth.After mixing and stirring the surface coating materials, apply the float evenly on the middle coating with a float knife, forming a surface layer of anti-dust, anti-corrosion, wear-resistant, smooth and bright self-leveling.

　　The performance characteristics of

　　Epoxy resin floor paint has the characteristics of strong acid and alkali resistance, wear-resisting, pressure resistance, impact resistance, mildew resistance, waterproof, dustproof, anti-skid, anti-static electricity, electromagnetic wave and so on.It is a one-time coating process, no matter how large the area, there is no joint, and it is also a non-dust material, with strong adhesion, anti-friction, hardness and other characteristics.

　　1. Dustproof, moisture-proof and wear-resistant;

　　2. Easy to clean, fast construction, convenient maintenance and low cost;

　　3. Strong adhesion, good flexibility and shock resistance;

　　4, the thickness of 0.2-0.3 ㎜.

　　Curing is introduced

　　1. It is recommended that pedestrians wear shoes with soft soles (if on-site conditions permit) and clean the hard materials such as sand particles on the soles of the soles before entering the industrial floor area, so as to reduce the scratches on the surface of the floor caused by sharp objects.

　　2. Handle the goods as lightly as possible to prevent heavy objects from hitting the ground, so as not to cause man-made damage.

　　Epoxy resin floor

　　Epoxy resin floor

　　3. The workshop of the epoxy floor paint on driving must pay attention to the speed is too fast, so as to avoid the brake behavior due to shear heat is too high, so as to make the epoxy floor paint instant softening (epoxy floor paint the softening temperature of around 80 ℃, thus the general control under 50 ℃) using the environment temperature and under the action of shear force is difficult to clean a stain.

　　4. Daily cleaning usable floor cleaner or wet cloth to wipe, can choose neutral detergent to clean, also can use general detergent with smaller made cleaning fluid concentration in the water, then use the floor cleaner or cotton mop wash the floors surface stains, use water to wash it again, dry ground;Pay attention to the paint edge of the floor do not have water for a long time.

　　5. It is recommended to use special floor wax or emulsified water-based wax for irregular waxing treatment (usually once a month);Clean and dry the floor with a floor cleaner or cotton mop, then wax it.Waxing treatment can increase the abrasion resistance and scratch resistance of any floor materials.

　　6. Avoid hitting the ground with heavy objects or tools, and do not drag heavy objects directly onto the epoxy floor.

　　7. Avoid the heavy corrosive medium to soak the floor paint film for a long time. If the corrosive acid and alkali are not spilled carefully, please clean the acid and alkali media timely.