| 品牌 |
乐泰 |
型号 |
汉高乐泰M-31CL |
| 硬化/固化方式 |
湿固化胶粘剂 |
主要粘料类型 |
合成弹性体 |
| 基材 |
透明无机材料 |
物理形态 |
膏状型 |
| 粘合材料类型:玻璃,塑料类,金属类,陶瓷,其他 | 树脂胶的分类:环氧树脂胶 |
| 热熔胶类型:其他热熔胶 | 剪切强度:3000（mpa） |
| 有效物质≥:90（％） | 活性使用期:5（min） |
| 工作温度:75（℃） | 保质期:24（个月） |
| 执行标准:coc | cas:sgs |
乐泰m-31cl环氧树脂胶粘剂
基本性能
外观透明度/颜色：灰白色
固化类型：室温/聚氨酯
适用基材：热塑性塑料，热固塑料，聚碳酸酯，弹性体，金属，玻璃，陶瓷
粘度：37000
温度范围：-53°c到149°c
更多产品详情，欢迎咨询深圳市鹏科泰贸易有限公司
电话： 86381822
传真：
product deion
loctite® m-31cl? provides the following product
characteristics:
technology epoxy
chemical type epoxy
appearance (resin) clear colorless to slightly yellow
liquidlms
appearance (hardener) clear colorless to slightly yellow
liquidlms
appearance (mixed) ultra clear
components two part - resin & hardener
viscosity low
mix ratio (by weight)
resin : hardener
100 : 46
mix ratio (by volume)
resin : hardener
2 : 1
cure room temperature cure after mixing
application bonding
loctite® m-31cl? cures at room temperature once mixed,
to form an ultra-clear adhesive bondline with excellent impact
resistance and minimal shrinkage. the fully cured epoxy is
resistant to a wide range of chemicals and solvents and has
excellent dimensional stability over a wide temperature range.
typical applications include bonding, small potting, staking and
laminating applications where optical clarity and excellent
structural, mechanical and electrical insulating properties are
required. loctite® m-31cl? bonds most materials including
glass, optical fibers, ceramics, metals, and many rigid plastics.
suitable for use in the assembly of disposable medical
devices
iso-10993
an iso 10993 test protocol is an integral part of the quality
program for loctite® m-31cl?. loctite® m-31cl? has
been qualified to loctite's iso 10993 protocol as a means to
assist in the selection of products for use in the medical device
industry. certificates of compliance are available at
through the henkel loctite quality
department.
typical properties of uncured material
resin:
specific gravity @ 25 °c 1.1
flash point - see msds
viscosity, brookfield - rvt, 25 °c, mpa·s (cp):
spindle 6, speed 20 rpm 9,000 to 12,000lms
hardener:
specific gravity @ 25 °c 1.0
flash point - see msds
viscosity, brookfield - rvt, 25 °c, mpa·s (cp):
spindle 5, speed 20 rpm 1,500 to 9,000lms
mixed:
specific gravity @ 25 °c 1.07
typical curing performance
gel time
gel time, 100 °c, seconds 90 to 150lms
working life
working life, minutes 30
tack free time
tack free time is the time required to achieve a tack free
surface.
tack free time, (low humidity), minutes 160
loctite material specificationlms
lms dated february-23, 2000. test reports for each batch are
available for the indicated properties. lms test reports include
selected qc test parameters considered appropriate to
specifications for customer use. additionally, comprehensive
controls are in place to assure product quality and
consistency. special customer specification requirements may
be coordinated through henkel quality.
storage
store product in the unopened container in a dry location.
storage information may be indicated on the product container
labeling.
optimal storage: 8 °c to 21 °c. storage below 8 °c or
greater than 28 °c can adversely affect product properties.
material removed from containers may be contaminated during
use. do not return product to the original container. henkel
corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. if additional information is required,
please contact your local technical service center or
customer service representative.
13925200833