| 品牌 |
乐泰 |
型号 |
乐泰220 |
| 产品名称 |
厌氧胶 |
硬化/固化方式 |
UV胶/紫外线胶/无影胶 |
| 主要粘料类型 |
合成热塑性材料 |
基材 |
透明无机材料 |
| 物理形态 |
乳液型 |
性能特点 |
螺纹锁固、密封 |
| 用途 |
螺纹锁固、密封 |
有效成分含量 |
99 |
| 生产执行标准 |
CFIA |
外观 |
蓝色 |
| 使用温度 |
-54-149 |
固含量 |
85 |
| 粘度 |
20 |
180°剥离强度 |
/ |
| 剪切强度 |
/ |
拉伸强度 |
/ |
| 扭剪强度 |
/ |
上胶厚度 |
/ |
| 固化时间 |
24 |
固化后硬度 |
/ |
| 老化时间 |
/ |
包装规格 |
250ML |
| 储存方法 |
室温 |
保质期 |
24个月 |
| 产地 |
山东 |
厂家 |
汉高股份有限公司 |
| 粘合材料类型:电子元件,金属类,其他 | 树脂胶的分类:丙烯酸酯胶 |
| 热熔胶类型:其他热熔胶 | 剪切强度:3000（mpa） |
| 有效物质≥:90（％） | 活性使用期:2（min） |
| 工作温度:75（℃） | 保质期:24（个月） |
| 执行标准:coc | cas:sgs |
| 应用领域:电子，工业等 |
具体价格面议
乐泰厌氧胶220
product deion
loctite® 220 is a low strength anaerobic threadlocking
compound designed for pre or post-application to small plated
fasteners. it prevents loosening while allowing adjustment or
easy removal.
typical applications
recommended for metal fasteners 2-56 through 10-32 screw
sizes.
properties of uncured material
typical value
chemical type methacrylate ester
appearance blue fluorescent liquid
specific gravity 1.08
viscosity, cp or mpa.s @ 77of
(25oc) cannon fenske #150
20
flash point (tcc), °c (°f) >200of (93oc)
typical curing performance
cure speed vs. temperature
the rate of cure will depend on the ambient temperature. full
cure is attainable in 24 hours at room temperature, 22°c
(72°f), or 1 hour at 93°c (200°f).
performance of cured material
after 24 hr at 72°f (22oc):
typical value
breakaway torque on steel 3/8 x 16
nuts and bolts in accordance with
mil-s-46163 procedures
in.lb. (nm) 85 (10)
prevail torque on steel 3/8 x 16
nuts and bolts in accordance with
mil-s-46163 procedures
in.lb. (nm) 170 (20)
where breakaway torque is the force required to initiate the fastener
movement and prevail torque is the force required to disassemble the
fastener once breakaway torque has occurred.
this product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
proper application method
proper application on through-hole assemblies involves filling
male, female or both threads with adhesive. for blind-hole
(non thorugh-hole) assemblies, adhesive should be applied
into the bottom of the hole. fastener installation will
hydraulically force adhesive upward into the threads.
material compatibility
loctite anaerobic adhesives/sealants can be used in
conjunction with all metals, glass ceramics and many
thermoset plastics such as phenolic and polyester. liquid
adhesives will, however, soften and sometimes craze
thermoplastics including abs, polycarbonate, vinyl and methacrylates.
they will also soften varnish and lacquer finishes.
most bake**mel finishes are not harmed by initial contact,
but should be wiped clean within an hour of application. the
cured loctite 220 adhesive will not affect any of these
materials.
disassembly and cleanup procedure
to aid in disassembly, loctite anaerobic compounds can be
weakened by heating to at least 500of (260oc). once
disassembled, cured adhesive can be removed with chisel®
gasket remover 790 by following instructions. a solvent wipe
with an organic or petroleum solvent will remove uncured
adhesive outside the joint.
storage
products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8° to 28°c
(46° to 82°f) unless otherwise labeled. optimal storage is at
the lower half of this temperature range.
优势方面
我们是胶粘剂及施胶设备整体解决方案供应商，我们不止卖产品，我们更为客户提供全面而的售前指导和售后服务工作，直至广大客户的项目正常运转！
预知更多产品详情，欢迎咨询深圳市鹏科泰贸易有限公司
13925200833