联系人：赖志平
邮箱：
电话：18664396232
地址： 福建厦门市思明区厦门市思明区吕岭路1733号创想中心2009-2010单元
| 品牌 |
GE发那科 |
型号 |
IC698PSD300 |
| 类型 |
Genius总线控制器 |
性能 |
良好 |
| 适用范围 |
高压系统 |
加工定制 |
否 |
| 串行端口 |
1(手持监视器端口) |
系列 |
90-70系列 |
| 所需电流 |
背板1.3安培 |
背板电压 |
5伏DC |
| 位置 |
RX3i串行扩展底板和90-30系列扩展底板 |
支持的通信 |
数据报和全局数据通信 |
| 最大支持设备数 |
总线上有32个设备 |
波特率 |
153.6、38.4或6.8千波特 |
IC698PSD300是GE Fanuc为RX7i系列制造的多用途高容量24 VDC、300瓦电源。它的输出功率可达300瓦，工作电压为18至30伏直流电，需要强制空气冷却。
该电源模块为RX7i背板模块提供逻辑电平的时序信号。它还提供过压故障条件、过流和过温保护。
强大的托盘风扇将空气强制送入电源的引擎，从而促进了冷空气的供应。该风扇安装在机架底部。IC698PSD300还有一个气流传感器，可以检测风扇故障或空气堵塞。如果电源感应到气流中断，它会关闭所有输出并打开超温LED指示灯(红色)。当内部温度降低到工作水平时，电源会自动从这种状态中恢复。
这IC698PSD300模块的三个led与气流传感器一起工作。绿色输出正常表示所有三个DC输出通道都在规定范围内工作。只有当三个DC输出通道中的一个出现故障时，它才会关闭。如果临界供应温度超过其极限，或者如果气流传感器检测到气流中断，红色超温LED将警告用户。
重要警告:当电源或任何外部连接的电源打开时，不要插入或移除模块。可能存在导致人身伤害、模块损坏或设备或过程意外运行的危险电压。
| 标称额定电压: | 24伏直流电 | |||||||||||
| 输入电压范围: | 18至30伏直流电 | |||||||||||
| 输入功率: | 430瓦 | |||||||||||
| 输出电压: | + 5伏直流电、+12伏直流电或-12伏直流电 | |||||||||||
| 模块类型: | 电源 | |||||||||||
| 机架位置: | 插槽0(最左边的插槽 The IC698PSD300 is a Multi-Purpose High Capacity 24 VDC, 300 Watt Power Supply manufactured by GE Fanuc for series RX7i. It provides a maximum output of up to 300 watts, operates from 18 to 30 VDC, and requires forced air cooling. This power supply module offers a logic level of sequencing signals to the RX7i backplane modules. It also offers protection against overvoltage fault conditions, overcurrent, and overtemperature. Provision of cool air is facilitated by a powerful tray fan that forces air into the power supply’s engine. This fan is mounted at the bottom of the rack. The IC698PSD300 also has an airflow sensor that detects fan failure or air blockage. If the power supply senses any interruption in air flow, it responds by switching off all outputs and turning on the over temperature LED indicator (RED). The power supply automatically recovers from this condition when the internal temperature decreases to operating levels. The IC698PSD300 module’s three LEDs work together with the airflow sensor. The green OUTPUT OK indicates that all the three DC output channels are operating within the specified range. It only turns OFF if one of the three DC output channels has failed. The red OVER TEMP LED will alert the user if the critical supply temperature exceeds its limit or if the airflow sensor detects interruption of air flow. Important warning: Do not insert or remove modules when the power supply or any externally-connected power sources are on. Hazardous voltages could exist resulting in personal injury, module damage, or unexpected operation of the device or process.
)
|
18664396232