3500/62-04-01 过程变量监控器BENTLY本特利

　　3500/62-04-01 过程变量监控器BENTLY本特利

　　3500/62-04-01 过程变量监控器BENTLY本特利

　　产品介绍

　　型号名称：3500-34模拟量模块

　　一、 用途极特性

　　用途：本测定仪使用于木质纤维类物质和竹制品、木器、中药材、烟草、棉花、纸张等的百分含水率测试。

　　特性：该仪表集测量器、显示器、电源、线路板于一体、体积小、重量轻、测量迅速、操作极为简单，也便于随身携带。

　　二、 主要技术指标

　　1、 显示形式：发光二极管发光显示，共2×10位

　　2、 测量范围：

　　量程Ⅰ 7-15%

　　量程Ⅱ 16-35%

　　3、 测量精度：±1位显示值（含水率）

　　4、 工作电压：直流15V（使用10F-20电池一节）

　　5、 使用条件：木材温度0-40℃环境相对温度＜85%

　　6、 外形尺寸：185×50×27

　　7、 重量：180克

　　三、使用方法

　　1、 装干电池：按电池正负极性把15V干电池装入电池盒内，正极向上。

　　2、 检查：使左右刚针短路（用手或金属连通）按下量程按纽Ⅰ，这是最下面的一只发光管应发光，其它发光管则不应发光、左右刚针闭路（无导电物连接）时，按下量程纽这时发光管都应不发光，如果能遇到上述要求表示仪器正常，可以进行测量。

　　3、 测量：把测量器四枚刚针插入木材中深6毫米，按下量程开关读出显示器发光位所对应的读数。如果按下的是量程Ⅰ按纽，则读右面一行读数。

　　Product introduction

　　Model name: 3500-34

　　1、 Application pole characteristics

　　Usage: this tester is used to test the percentage moisture content of wood fiber substances, bamboo products, woodwork, traditional Chinese medicine, tobacco, cotton, paper, etc.

　　Features: the instrument integrates measuring device, display, power supply and circuit board. It has the advantages of small volume, light weight, rapid measurement, extremely simple operation and easy to carry.

　　2、 Main technical indicators

　　1. Display form: LED light-emitting display, 2 in total × 10 digits

　　2. Measuring range:

　　Range I 7-15%

　　Range Ⅱ 16-35%

　　3. Measurement accuracy: ± 1 digit display value (moisture content)

　　4. Working voltage: DC 15V (one 10f-20 battery is used)

　　5. Service conditions: Wood temperature 0-40 ℃, ambient relative temperature < 85%

　　6. Overall dimension: 185 × fifty × twenty-seven

　　7. Weight: 180g

　　3、 Method of use

　　1. Install dry battery: install the 15V dry battery into the battery box according to the positive and negative polarity of the battery, with the positive pole upward.

　　2. Check: short circuit the left and right rigid needles (connect by hand or metal) and press the measuring range button I. This is the lowest light-emitting tube that should emit light, while other light-emitting tubes should not emit light. When the left and right rigid needles are closed (without conductive connection), press the measuring range button, and then the light-emitting tubes should not emit light. If the above requirements are met, it means that the instrument is normal and can be measured.

　　3. Measurement: insert the four rigid needles of the measuring device into the wood to a depth of 6mm, press the range switch to read the reading corresponding to the luminous position of the display. If the range I button is pressed, read the right line.