变电所开关柜无线测温装置

　　变电所开关柜无线测温装置and the measurement accuracy is high. After testing the bus current is greater than 8A, the wireless temperature measuring module can work stably after receiving power through CT induction. It solves the problem of frequent battery replacement by traditional battery power supply, and can monitor the temperature of the equipment in the high voltage switch cabinet without being affected by the large range of current changes, so as to ensure the normal operation of the high voltage switch cabinet.

　　产品简介

　　功能：

　　ARTM-Pn无线测温装置:ARTM-Pn无线测温装置可以单独安装在高压柜、低压抽屉柜内，每台装置可以接收18个传感器的数据，传感器型号可选配ATE100、ATE200、ATE300。装置带有一路485接口，可将采集到的温度数据上传到监控中心。

　　ARTM8温度巡检仪:ARTM系列温度巡检测控仪适用于一路或多路温度的测量和控制，主要应用于火电厂、水电站等场合的温度巡检测量及控制。测量8通道Pt100温度，也可以屏蔽其中任意通道。每一通道温度测量对应2段报警，继电器输出可以任意设置报警方向及报警值。

　　无线测温集中采集触摸屏:无线测温触摸屏可以嵌入式安装在高压柜、低压抽屉柜内，每台装置可以接收240个传感器的数据，可与ATE100、ATE200、ATE300三种传感器选配使用。装置带有一路485接口、可选配一路以太网口，可将采集到的温度数据上传到监控中心。

　　应用范围：

　　适用于高低压开关柜内电缆接头、断路器触头、刀闸开关、高压电缆中间头、干式变压器、低压大电流等设备的温度监测。

　　订货范例：

　　技术要求：1面高压柜内断路器触头6点、母排3点无源无线测温

　　辅助电源：AC/DC 220V

　　显示方式：单独无线温度显示

　　综上所述，确定型号为：无线测温装置：ARTM-P9-300,1台;无线测温传感器：ATE300,9个

　　订货范例：

　　技术要求：10面高压柜内断路器触头6点、母排3点无线测温

　　无线传感器要求：电池供电、无线

　　显示方式：集中无线温度显示

　　综上所述，确定型号为:无线测温集中触摸屏：AARTM-7062HT-4(HI),1台；无线测温传感器：ATE200,90个；无线测温收发器：ATC200,10个

　　订货范例：

　　技术要求：10面高压柜内断路器触头6点、母排3点无线测温

　　无线传感器要求：无源无线

　　显示方式：集中无线温度显示

　　综上所述，确定型号为：无线测温集中触摸屏：ARTM-7062HT-4(HI),1台；无线测温传感器：ATE300,90个；无线测温收发器：ATC400,1个；电源模块：ARTM-KDYA-DG30-24K，1个。

　　技术指标

　　产品功能

　　外形尺寸

　　产品报价

　　To configure the microcontroller and wireless transceiver, in order to prevent the node crash, design the watchdog program; In order to be able to enter hibernation mode three, power management and core voltage monitoring Settings; In order to prevent each node from sending data at the same time, random delay algorithm is adopted. In order to reduce power consumption, the temperature sensor chip is turned off, as shown in the following figure. Controlled by single chip microcomputer 10 power transistor temperature sensor chip off and AD sampling concrete implementation wireless temperature measurement system software flow chart shown in figure 5, the main working principle of the single chip microcomputer to enter sleep mode the Halt, single-chip microcomputer in stop state, need to wake up regularly, set up internal RTC clock as a timer, awakens the single-chip temperature sampling regularly, After sampling, the wireless transmission module is set to work after the MCU wakes up next time, and the temperature data is sent to the host. The wireless temperature measurement system based on inductive power acquisition runs well in the practical application of high voltage switchgear. The system can measure the temperature of the temperature monitoring point in real time,

　　变电所开关柜无线测温装置