进口倒置桶疏水阀 倒吊桶蒸汽疏水器 美国RETZ瑞茨

　　品牌：RETZ瑞茨/我们一直致力于流体控制和测控领域的持续创新，始于2005……(吊桶)倒置桶蒸汽疏水阀性能可靠，几乎可为所有蒸汽输送管线，伴热管线和蒸汽设备提供高效疏水。倒置桶在壳体内长期稳定可靠地工作，既降低维修费用，又节约蒸汽能源 Theinverted bucket steam trap has reliable performance and can provide efficientdrainage for almost all steam transmission pipelines, heat tracing pipelines,and steam equipment. The inverted bucket operates stably and reliably in theshell for a long time, reducing maintenance costs and saving steam energy

　　主要性能 Mainperformance

　　倒置桶蒸汽疏水阀采用球面密封，拉杆耐磨损性好，阀芯更深地陷入阀座，从而保持了密封性，阀芯支架与特殊设计而成的"超级杠杆"相配合。阀芯在支架内是自由浮动的，避免了关闭时产生的刚性碰撞 RETZinverted bucket steam drain valve adopts spherical seal, with good wearresistance of the pull rod. The valve core is deeper into the valve seat, so asto maintain the tightness. The valve core support is matched with the speciallydesigned "super lever". The valve core is free floating in thebracket to avoid rigid collision during closing

　　性能特点∶

　　可承受高背压，可达90%

　　抗水击∶开口吊桶结构不会因水击而遭损坏 Water hammer resistance: the open bucketstructure will not be damaged by water hammer

　　阀体内设有滤网，且阀瓣与阀座位于阀体的顶部，污物不会存积在阀孔处 The valve body is provided with a filterscreen, and the valve disc and the valve seat are located at the top of thevalve body. Dirt will not be accumulated at the valve hole

　　球面密封无集中磨损，关闭阀座孔时，由于采用了浮动杠杆机构，具有软着陆特点，提高了使用寿命 The spherical seal has no concentrated wear.When the valve seat hole is closed, the floating lever mechanism is adopted,which has the characteristics of soft landing and improves the service life

　　独特的杠杆机构将倒置桶重力放大，以便开启受到系统压差作用的阀瓣。杠杆机构为自由浮动式，没有固定支点造成的磨损 The unique lever mechanism enlarges thegravity of the inverted bucket to open the valve disc affected by the systempressure difference. The lever mechanism is free floating, without wear causedby fixed fulcrum

　　排放口完全被水封包围，可防止新鲜蒸汽损失 Thedischarge port is completely surrounded by water seal to prevent the loss offresh steam

　　倒置桶疏水阀排放动作是间断的，但其凝结水排放是连续的，不存在凝结水的积聚问题 RETZThe discharge action of the inverted bucket drain valve is intermittent, butthe condensate discharge is continuous, and there is no accumulation ofcondensate

　　性能参数performance parameter

　　规格尺寸：1/2-3"(法兰/内螺纹BSP、NPT) Specification and size: 1 / 2-3 "(flange/ internal thread BSP, NPT)

　　公称压力：16-40BarNominal pressure: 16-40bar

　　压差范围:0.1-30BarOperating pressure difference range: 0.1-30bar

　　介质温度：≤300℃ Medium temperature: ≤ 300 ℃

　　1.阀体GGG40/A216WCB/A351 CF8

　　2.阀盖GGG40/A216WCB/A351 CF8

　　3.堵头ASTM A105

　　4.阀盖螺栓A193 B7

　　5.套圈A276 304

　　6.阀芯导杆A276 304

　　7.连杆螺栓A194 B8

　　8.阀座A276 430

　　9.阀芯A276 430

　　10.阀芯连杆A276 304

　　11.阀芯固定片A240 304

　　12.吊桶 A240 304

　　13.过滤网A240 304

　　14.过滤器堵头ASTM A105

　　按箭头所示安装，注意疏水阀处于水平位置或低于设备出口，以保证正常疏水Please install as shown by the flow arrow on the valve body. Note that thedrain valve is at the horizontal position or lower than the equipment outlet toensure normal drainage